No start. 2001 chevy van 1500 conversion Van.
Hello, I had to pull dash facia on my van yesterday. I unplugged headlight switch wires. Found I could not repair dome overide without replacing whole unit. r
Replaced and now vehicle starts and shuts down immeadiatly. Did I set off security and how do I reset it ? Needin some help here.
2001 Chevy Van No Start Security Problem Re-learn Procedure
Re: No Start Security Problem Re-learn Procedure
Not sure how removing the facia could cause a problem with the FACTORY security system, but here is a relearn procdure that may help...
•Turn ON the ignition, with the engine OFF.
•Attempt to start the engine, then release the key to ON, vehicle will not start.
•Observe the SECURITY telltale, after approximately 10 minutes the telltale will turn OFF.
•Turn OFF the ignition, and wait 5 seconds.
•Repeat steps 1 through 4 two more times for a total of 3 cycles/30 minutes. The vehicle is now ready to relearn the Passlock™ Sensor Data Code and/or passwords on the next ignition switch transition from OFF to CRANK.
Important: The vehicle learns the Passlock Sensor Data Code and/or password on the next ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle.
•Start the engine. The vehicle has now learned the Passlock Sensor Data Code and/or password.
•With a scan tool, clear any DTCs if needed. The history DTCs will self clear after 100 ignition cycles.
•Turn ON the ignition, with the engine OFF.
•Attempt to start the engine, then release the key to ON, vehicle will not start.
•Observe the SECURITY telltale, after approximately 10 minutes the telltale will turn OFF.
•Turn OFF the ignition, and wait 5 seconds.
•Repeat steps 1 through 4 two more times for a total of 3 cycles/30 minutes. The vehicle is now ready to relearn the Passlock™ Sensor Data Code and/or passwords on the next ignition switch transition from OFF to CRANK.
Important: The vehicle learns the Passlock Sensor Data Code and/or password on the next ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle.
•Start the engine. The vehicle has now learned the Passlock Sensor Data Code and/or password.
•With a scan tool, clear any DTCs if needed. The history DTCs will self clear after 100 ignition cycles.
-
- Similar Topics
- Replies
- Views
- Last post
-
-
New post GMC 2001 Sierra does not always start!
by rkcrump » Wed Oct 19, 2016 8:37 pm » in GMC Trucks - 1 Replies
- 4385 Views
-
Last post by carriedi
Wed Oct 19, 2016 10:54 pm
-
-
-
New post 2001 Chevy suburban won't stay running
by Trudy » Sun Jul 22, 2018 3:00 am » in Chevy Suburban - 1 Replies
- 11720 Views
-
Last post by carriedi
Tue Jul 24, 2018 8:55 am
-
-
-
New post 2001 chevy silverado 1500 4.8 new alt and battery, still die
by AcurazFinest52 » Tue Jul 25, 2017 9:52 am » in Chevy Silverado - 4 Replies
- 23966 Views
-
Last post by carriedi
Mon Jul 31, 2017 3:28 am
-
-
-
New post 2001 Chevy 4.3 Blazer Trany stays in 2nd & speedo @ zero
by roy33 » Fri Jan 06, 2017 12:10 pm » in Chevy Blazer - 1 Replies
- 9731 Views
-
Last post by carriedi
Sat Jan 07, 2017 1:11 pm
-