Clutch drag and hard shifting
Clutch drag and hard shifting
I put a new slave cylinder and clutch kit and my 96 Saturn SL 2. Now, as experiencing clutch drag And shifting hard.What is this from
Re: Clutch drag and hard shifting
it sounds like you are not getting enough travel from the clutch slave to completely release the clutch disc. That means that the input shaft is still spinning when you are trying to shift gears.
how does your clutch pedal feel?
did you do a slave cylinder or did you replace the master, line and slave altogether as one piece?
how does your clutch pedal feel?
did you do a slave cylinder or did you replace the master, line and slave altogether as one piece?
- Attachments
-
- saturn master+slave.jpg (27.58 KiB) Viewed 11099 times
Browse "SIMILAR TOPICS" At The Bottom Of This Page.
Re: Clutch drag and hard shifting
New clutch stage 1 New master slave cylinder whole unit stand alone system per filled and blead clutch peddle fine same as it always was travel fine the funny thing is if u pump clutch peddle it stops I was told air in the system so one min it's fine next it's dragging again I'm at a loss here and I want to put one more tool to use a block of c4
Re: Clutch drag and hard shifting
Installed all New stage 1 clutch New master/slave cylinder whole unit stand alone system pre bled and filled all New parts when u pump the clutch 1000000 time it work for a bit clutch peddle fine same as it always was travel fine and when the car warms up it starts creeping again I'm at a loss I put two new slave master cylinders in and same thing feels like air in the system
Re: Clutch drag and hard shifting
I messed up and put GM Manuel trans fluid and not atf I quickly changed the fluid to atf n that is after first start of shifting problems and the fluid got changed again and it can out smelling really burnt and smelled bad
Re: Clutch drag and hard shifting
you could also check your shifter cables. I have seen cables that start coming apart and then make it hard to shift. I have even seen the cable break and they can't shift gears. but your really sounds like the slave isn't moving enough to free up the disc.
why did you do the clutch? How was the clutch fork and ball stud when you had the trans off?
why did you do the clutch? How was the clutch fork and ball stud when you had the trans off?
Browse "SIMILAR TOPICS" At The Bottom Of This Page.
Re: Clutch drag and hard shifting
All new cables I guess I'm not say the right things but I've told u everything I did to this car and I'm not getting any kind of straight answer's on this from any where and the fork is fine this is all happening when the car gets warm even the clutch drag
Re: Clutch drag and hard shifting
I've put two clutches in the car when I bought the car it was going due to bad driving and now knowing that the master/slave cylinder had it's help in destroying the first clutch I put in so thus time put the stage 1 New everything it's freezing here and I can go out there right now and it will run awesome like screams down the road like a bat outta hell but as soon as it reads 1/4 temp it's starts clutch drag and slite crunching of gears then at full temp crap crap crap
Re: Clutch drag and hard shifting
When at full temp double clutching works good
-
- Similar Topics
- Replies
- Views
- Last post
-
-
New post Hard shifting 1st an 2nd gear code P0010
by Lesfry86 » Wed Jul 02, 2014 10:58 pm » in Chevy Cars - 13 Replies
- 50291 Views
-
Last post by Lesfry86
Mon Jul 07, 2014 11:07 pm
-
-
- 5 Replies
- 29620 Views
-
Last post by carriedi
Thu Jul 31, 2014 9:51 pm
-
- 1 Replies
- 3886 Views
-
Last post by carriedi
Sun Jul 10, 2016 2:31 am
-
-
New post High revs when clutch depressed
by charliebrownboy » Tue Mar 17, 2015 4:56 pm » in Ford Cars - 4 Replies
- 6046 Views
-
Last post by raneger
Mon Jun 01, 2015 4:18 am
-
-
-
New post high revs when depressing clutch - ford focus zetec 1.8 1998
by charliebrownboy » Sat Aug 23, 2014 4:09 pm » in Ford Cars - 2 Replies
- 6407 Views
-
Last post by charliebrownboy
Thu Aug 28, 2014 3:11 pm
-