1999 Dodge Durango 5.2 slt
-
- Posts: 2
- Joined: Wed Mar 25, 2015 9:48 pm
Dodge shuts off after releasing pressure off the ignition sw
I have a 1998 Dodge 1500 king cab two wheel drive, when I try to crank it by the ignition switch it does nothing but when I by pass the ignition switch and use a jumper wire it will only crank with the ignition switch in a certain place, when I slightly move the ignition switch it shuts off. What could be the problem and how hard is it to fix?
Re: Dodge shuts off after releasing pressure off the ignitio
where are you jumping the starter from and to?
the first thing I would check is your starter relay. You should get power from the yellow wire from the ignition switch that goes to the clutch switch (if you have a manual trans) then it goes to the starter relay. From the starter relay it goes to the neutral safety switch to ground (if you have an automatic trans) the relay gets power from the battery through a pink and black wire from the power distribution box, fuse #2 (30A). Sends the power out on the brown wire that goes to the starter solenoid.
so you would have to see if you have all the correct powers and grounds first, then see what is happening when you turn the ignition switch to start. Is the neutral safety switch grounded in park and neutral? Are you getting your full battery voltage from the yellow wire. The starter fuse should be good or it would never start. The relay could be bad. the switch could be bad, the clutch switch could be bad, the neutral safety switch could be bad, or the starter could be bad.
You have to start from one end and follow it through until you find where the circuit stops.
the first thing I would check is your starter relay. You should get power from the yellow wire from the ignition switch that goes to the clutch switch (if you have a manual trans) then it goes to the starter relay. From the starter relay it goes to the neutral safety switch to ground (if you have an automatic trans) the relay gets power from the battery through a pink and black wire from the power distribution box, fuse #2 (30A). Sends the power out on the brown wire that goes to the starter solenoid.
so you would have to see if you have all the correct powers and grounds first, then see what is happening when you turn the ignition switch to start. Is the neutral safety switch grounded in park and neutral? Are you getting your full battery voltage from the yellow wire. The starter fuse should be good or it would never start. The relay could be bad. the switch could be bad, the clutch switch could be bad, the neutral safety switch could be bad, or the starter could be bad.
You have to start from one end and follow it through until you find where the circuit stops.
- Attachments
-
- 1998 Dodge 1500 king cab starter relay and ignition wiring diagram.
- 98 dodge starter.jpg (117.47 KiB) Viewed 29282 times
1999 Dodge Durango 5.2 slt
Last time it started it wouldnt hold an idol, it just died if i let off the gas. Now it wont start at all. I replace the relays, replaced the starter, replaced the battery, I took the spark plugs out, turned the flywheel manually, AND I checked all the fuses(all good every one of them even the hidden). If I put my foot on the break when I turn the key nothing happens the lights in the dash don’t let up there’s no beings nothing happens except for once there was this weird click click click click click coming from the glove box. If I take my foot off the break and turn the key all the lights come on like they’re supposed to the beings happen like they’re supposed to the fuel pump and gauges everything works all the way to the starter clicking on the fly wheel . But it will not start. What the hell is wrong with my Dodge? please if you have any idea I would love to hear it.
Re: 1999 Dodge Durango 5.2 slt
I would look for the grounds to the body and the engine.
check for a voltage drop between the battery and the power at the fuse box and through the ignition switch.
you have replaced a lot of parts. what started all the work you have done? What was the first symptom that you noticed?
from what you have described so far seem to be that you do not have enough current to run the circuits needed. That could be that there is too much resistance in the circuits from the battery. Or a ground is not grounded somewhere.
check for a voltage drop between the battery and the power at the fuse box and through the ignition switch.
you have replaced a lot of parts. what started all the work you have done? What was the first symptom that you noticed?
from what you have described so far seem to be that you do not have enough current to run the circuits needed. That could be that there is too much resistance in the circuits from the battery. Or a ground is not grounded somewhere.
help
I have a 2002 Durango 4.7l my problem is I can only drive 50mph pedal all the way to floor. I have checked every sensor and injectors and coils all seem good no codes when scan is run.fuel pressure is good.also when I unhook all odd coils it does not change a thing. when I unhook all the even coils and hook up the odd coils, truck will not start.any advice would be a appreciated
-
- Similar Topics
- Replies
- Views
- Last post
-
-
New post 2006 Durango 5.7 Hemi rough idle/ETC problem
by jdharris717 » Sat Dec 30, 2017 12:31 pm » in Dodge And Chrysler - 5 Replies
- 17025 Views
-
Last post by jdharris717
Sat Jan 13, 2018 10:27 am
-
-
- 9 Replies
- 25607 Views
-
Last post by carriedi
Mon Jul 31, 2023 10:27 am
-
- 10 Replies
- 35579 Views
-
Last post by dw85745
Sat Feb 20, 2016 8:44 am
-
- 7 Replies
- 24571 Views
-
Last post by carriedi
Sun Sep 16, 2018 3:16 pm