ford taurus radio dont work after replacing the battery
ford taurus radio dont work after replacing the battery
i but a new battery in my 1999 ford taurus n now the raido dont work at all
Re: ford taurus raido dont work after replacing the battery
First thing to do is check the fuses. If you jump started it, or caused a spark when replacing the battery, you may have blown a fuse. You could have also damaged the radio if it does not work at all.
-
- Posts: 1
- Joined: Thu Aug 22, 2013 4:32 am
2006 ford Taurus Idle High
my car has been idling high for the past week I would have to floor the gas to get to 55mph. My rpm will go to 3 then 4 when I reach 55 it will go to 2 until I stop then it start all over again. Today it will start up but won't go into gear
Re: 2006 ford Taurus Idle High
sounds like you have two problems. 1. high idle 2. trans slip or not changing gears and now no trans engagement. High idle, I would look for a vacuum leak. (check pcv valve vacuum circuit) but, that's all secondary if you can't even drive the car. If your transmission won't go into any gear you probably will have to change or rebuild your trans. Check to make sure your transmission fluid is full. trans fluid should look red. Not dark brown or black. And it should not smell burnt. but, usually when Taurus transmissions no longer go into any gear they will need to be replaced
-
- Posts: 8
- Joined: Thu Oct 15, 2015 3:07 pm
1997 Sable - Proper Wrench for EGR Tubing Nut
Wanted to change the EGR valve on my 1997 Sable 3.0L Vulcan but I did not have the proper wrench to loosen the nut that attaches the EGR tubing to the EGR valve.
Does anyone know what is the size of that nut and/or what is proper size of a wrench to loosen it?
I do not want to pay big bucks to the dealer if I can do it myself.
Looked all over but no one seems to know the nut size and/or the proper sized wrench to use.
Info is appreciated
Does anyone know what is the size of that nut and/or what is proper size of a wrench to loosen it?
I do not want to pay big bucks to the dealer if I can do it myself.
Looked all over but no one seems to know the nut size and/or the proper sized wrench to use.
Info is appreciated
Re: 1997 Sable - Proper Wrench for EGR Tubing Nut
this video may help you
https://www.youtube.com/watch?v=74T0212uVgk
however, in the video He took off more than he needed to. Just take the big nut off and the two small bolts to take the egr valve all by itself and leave the engine part where it is. (just look at the new part and you will be able to see what should come off.
https://www.youtube.com/watch?v=74T0212uVgk
however, in the video He took off more than he needed to. Just take the big nut off and the two small bolts to take the egr valve all by itself and leave the engine part where it is. (just look at the new part and you will be able to see what should come off.
-
- Posts: 8
- Joined: Thu Oct 15, 2015 3:07 pm
Re: 1997 Sable - Proper Wrench for EGR Tubing Nut
The video is great but I need to know the specific size of the wrench used. In my case, the egr is attached to the block next to the Iac valve with the tubing directly attached to the valve with a large nut.
My egr setup is different than the one in the video.
My egr setup is different than the one in the video.
Re: 1997 Sable - Proper Wrench for EGR Tubing Nut
so then the 1 and 1/16 inch wrench the guy talks about in the video is not the size of the one in your car?
-
- Posts: 8
- Joined: Thu Oct 15, 2015 3:07 pm
Re: 1997 Sable - Proper Wrench for EGR Tubing Nut
His engine configuration is different from mine, so I cannot say for certainty that his wrench or nut size would fit.
I need someone who has my specific engine config for a 1997 Sable to tell me for sure.
I need someone who has my specific engine config for a 1997 Sable to tell me for sure.
Re: 1997 Sable - Proper Wrench for EGR Tubing Nut
so, you're not going to check to see if the 1 1/16" is correct then? Do you have and adjustable wench that can open that far?
-
- Similar Topics
- Replies
- Views
- Last post
-
- 4 Replies
- 30636 Views
-
Last post by carriedi
Mon Dec 28, 2015 6:17 pm
-
-
New post Ford F-350 Truck Illuminated Emblems
by RogerSan » Sat Feb 10, 2018 2:14 am » in Ford Trucks - 6 Replies
- 31754 Views
-
Last post by rusgrant83
Thu Mar 01, 2018 1:33 am
-
-
-
New post 1994 ford bronco xlt 5.8 351 win no heat
by Hlovell1977 » Tue Dec 13, 2016 2:04 pm » in Ford Trucks - 1 Replies
- 23498 Views
-
Last post by carriedi
Wed Dec 14, 2016 11:18 am
-
-
- 5 Replies
- 26189 Views
-
Last post by carriedi
Wed Apr 13, 2016 1:03 am
-
-
New post 2007 ford freestyle wrench light comes on and will not shift
by farmerdawn » Sun Aug 30, 2015 8:29 pm » in Ford Cars - 7 Replies
- 30439 Views
-
Last post by carriedi
Sat Nov 18, 2017 6:04 pm
-