99' Ford Explorer Sport turn signal multi switch
-
- Posts: 11
- Joined: Wed Jan 11, 2017 9:07 pm
99' Ford Explorer Sport turn signal multi switch
I'm searching for the color diagram for the multi switch. Which color wire goes to which pin.
I'm most interested in pin 1-8.
Thanks
I'm most interested in pin 1-8.
Thanks
Re: 99' Ford Explorer Sport turn signal multi switch
what pins are you looking for? Turn, wiper, high beams... (it looks like you should have two seven wire connectors)
if you just want colors:
684 pink/yel
359 gry/red
880 lt blu/org
44 lt blu
385 wht/red
3 lt grn/wht
9 dk blu/wht
5 brn/yel
2 wht/lt blu
511 lt grn
these are for high beams
dk blu/org
red/yel
gry/org
red/blk
if you just want colors:
684 pink/yel
359 gry/red
880 lt blu/org
44 lt blu
385 wht/red
3 lt grn/wht
9 dk blu/wht
5 brn/yel
2 wht/lt blu
511 lt grn
these are for high beams
dk blu/org
red/yel
gry/org
red/blk
- Attachments
-
- explorer multi switch.jpg (42.41 KiB) Viewed 21729 times
-
- explorer multi pins.jpg (34.35 KiB) Viewed 21729 times
Browse "SIMILAR TOPICS" At The Bottom Of This Page.
-
- Posts: 11
- Joined: Wed Jan 11, 2017 9:07 pm
Re: 99' Ford Explorer Sport turn signal multi switch
1999 Ford Explorer Sport
The wires were loose and fell out. Some may have been put back in the incorrect positions. Mainly the top portion pins 1-8.
I got a replacement harness from the junkyard and the some wires don't match. The discrepancy may be my own (my brother) fault but I'm unsure.
As you can see the discrepancy on terminal 4 & 7 and the reverse of wires colors 6 & 8. The missing wire from between pin 7 & 8 (blank).
the book shows pins 1-8 but I do see the higher numbers marks
pin 1 = 511
pin 2 = 3
pin 3 = 385
pin 4 = 44
pin 5 = 2
pin 6 = 6
pin 7 = 380
pin 8 = 5
blank = 379
I have posted 4 pictures for your review. 2 in this post and another 2 below it.
harness was tested for continuity between pins. all were 100%
The wires were loose and fell out. Some may have been put back in the incorrect positions. Mainly the top portion pins 1-8.
I got a replacement harness from the junkyard and the some wires don't match. The discrepancy may be my own (my brother) fault but I'm unsure.
As you can see the discrepancy on terminal 4 & 7 and the reverse of wires colors 6 & 8. The missing wire from between pin 7 & 8 (blank).
the book shows pins 1-8 but I do see the higher numbers marks
pin 1 = 511
pin 2 = 3
pin 3 = 385
pin 4 = 44
pin 5 = 2
pin 6 = 6
pin 7 = 380
pin 8 = 5
blank = 379
I have posted 4 pictures for your review. 2 in this post and another 2 below it.
harness was tested for continuity between pins. all were 100%
- Attachments
-
- FROM THE REPAIR BOOK
- img_0621.jpg (57.41 KiB) Viewed 21726 times
-
- HARNESS
- img_0623 NUMBERED_edited-1.jpg (59.83 KiB) Viewed 21726 times
-
- Posts: 11
- Joined: Wed Jan 11, 2017 9:07 pm
Re: 99' Ford Explorer Sport turn signal multi switch
see some of the wires are not matching...
pin 1, 2, 3, 5 match perfectly.
4 & 7 are switched
8 empty
6 & 8 reversed
pin 1, 2, 3, 5 match perfectly.
4 & 7 are switched
8 empty
6 & 8 reversed
- Attachments
-
- junkyard replacement
- img_0628 NUMBERED_edited-1.jpg (47.1 KiB) Viewed 21726 times
-
- harness on my truck
- img_0626 NUMBERED_edited-1.jpg (50.06 KiB) Viewed 21726 times
-
- Posts: 11
- Joined: Wed Jan 11, 2017 9:07 pm
Re: 99' Ford Explorer Sport turn signal multi switch
I'm guessing for starters. Pin 7 continuity has no match according to the book, so that might be in the wrong place.
I might have to move it to the 4 position since that has multiple matching points needed for continuity.
I might have to move it to the 4 position since that has multiple matching points needed for continuity.
-
- Posts: 11
- Joined: Wed Jan 11, 2017 9:07 pm
Re: 99' Ford Explorer Sport turn signal multi switch
carriedi wrote:
> what pins are you looking for? Turn, wiper, high beams... (it looks like
> you should have two seven wire connectors)
> if you just want colors:
> 684 pink/yel
> 359 gry/red
> 880 lt blu/org
> 44 lt blu
> 385 wht/red
> 3 lt grn/wht
> 9 dk blu/wht
> 5 brn/yel
> 2 wht/lt blu
> 511 lt grn
>
> these are for high beams
> dk blu/org
> red/yel
> gry/org
> red/
What about the other pin colors?
> what pins are you looking for? Turn, wiper, high beams... (it looks like
> you should have two seven wire connectors)
> if you just want colors:
> 684 pink/yel
> 359 gry/red
> 880 lt blu/org
> 44 lt blu
> 385 wht/red
> 3 lt grn/wht
> 9 dk blu/wht
> 5 brn/yel
> 2 wht/lt blu
> 511 lt grn
>
> these are for high beams
> dk blu/org
> red/yel
> gry/org
> red/
What about the other pin colors?
Re: 99' Ford Explorer Sport turn signal multi switch
how many wired connectors are in each harness connector?
yes, switch 4 and 7 by your numbering system would look to be correct.
the top picture appears to be the correct positions. If you have a trailer connector in the back of your truck you can check if the turn signals are to the correct side. If they are opposite then you need to switch the brn/yel and the drk blu/white wires.
yes, switch 4 and 7 by your numbering system would look to be correct.
the top picture appears to be the correct positions. If you have a trailer connector in the back of your truck you can check if the turn signals are to the correct side. If they are opposite then you need to switch the brn/yel and the drk blu/white wires.
Browse "SIMILAR TOPICS" At The Bottom Of This Page.
-
- Posts: 11
- Joined: Wed Jan 11, 2017 9:07 pm
Re: 99' Ford Explorer Sport turn signal multi switch
The lower harness is complete with no problems pins 9-15.
I switched 4 & 7 and all work. Light, wipers, turn, hazard, high, low.
Now 6 & 8 are hanging loose. No trailer connection to worry about.
I tested both 6 & 8 matching color to color and reversing the colors and I don't notice anything happening.
Should I just connect them?
I switched 4 & 7 and all work. Light, wipers, turn, hazard, high, low.
Now 6 & 8 are hanging loose. No trailer connection to worry about.
I tested both 6 & 8 matching color to color and reversing the colors and I don't notice anything happening.
Should I just connect them?
Re: 99' Ford Explorer Sport turn signal multi switch
yea, put them back into the connector. this way it will be a cleaner situation and if you ever do a trailer connector you should have the wiring available.
Browse "SIMILAR TOPICS" At The Bottom Of This Page.
-
- Similar Topics
- Replies
- Views
- Last post
-
- 1 Replies
- 5827 Views
-
Last post by carriedi
Thu Dec 04, 2014 5:05 am
-
- 1 Replies
- 3189 Views
-
Last post by carriedi
Thu Dec 07, 2023 1:30 pm
-
-
New post 1993 Mercury Cougar XR-7 Turn Signal & Brake Light Issues?
by 1964prostreetelcamino » Tue Jul 15, 2014 4:32 pm » in Ford Cars - 1 Replies
- 10358 Views
-
Last post by carriedi
Tue Jul 15, 2014 6:07 pm
-
-
- 1 Replies
- 9040 Views
-
Last post by carriedi
Fri Oct 02, 2015 3:01 am
-
-
New post Ford 2010 explorer 4.0 overheating when not accelerating
by Gildave » Mon Jul 18, 2016 5:10 pm » in Ford Trucks - 1 Replies
- 9409 Views
-
Last post by carriedi
Mon Jul 18, 2016 8:28 pm
-