96 z71 trans problem
Re: 700r4 tranny problems
Sounds like maybe a proble with the low roller clutch.
Internal for sure.
Internal for sure.
Be sure to check the Similar Topics down this page for more help.
96 z71 trans problem
I have a 96 z71 it ran good until it was envoled in a wreck on driver side now just test drove it first time after i fixed it and the trans is acting up shifts in to 1/2 but 2/3 shifts hard and it shifted into overdrive once but it went right back out. Now it wont shift into overdrive had to do some heavy fixing replaced the driver finder, hood, grill, headlights, interfinder well, radiator, clutch fan, and radiator support and driver door. What is worng with my truck?
Re: 96 z71 trans problem
you might want to take it to a transmission shop and have them drive the vehicle with a scanner on it to see what is happening according to the computer data stream.
Browse "SIMILAR TOPICS" At The Bottom Of This Page.
Re: 96 z71 trans problem
Ok thanks for ur help
-
- Posts: 1
- Joined: Sun Dec 08, 2013 11:33 am
engine/tranny moved back, now no reverse and tranny noise
Hi folks brand new here. I've got a weird situation with my buddies 02 silverado 2wd. It seems his engine/tranny slid back(?) against his fire wall. It looks fine under the hood to me as far as position except the passenger side rear spark plug wire is definitely touching fire wall. Then again, I'm not real familiar with this truck so I have no point of reference. He was getting on the freeway at about 35mph when he heard a thud and pulled over. He was able to limp it along home but tranny makes noise at above 25 - 30 mph. as well he now has no reverse. I looked under the rear cross member where the tranny mount is bolted to xmember and the washer seems to have moved back about 3/8". I jacked up the truck and then put a jack (carefully) under the engine to see if the rubber on the front mounts had seperated and had caused the engine/tranny to move but both sides seemed ok. The driver side did look separate but when jacking under engine, the whole front end lifted, telling me that the rubber hadn't separated. Also, the u joint had a dab tranny fluid on it. So, uhhhhhh? Anyone?
Re: engine/tranny moved back, now no reverse and tranny noi
The number 8 spark plug wire does just about hit the firewall, so that is normal. There is no way the engine and trans can slide back. If an engine mount was broke, the torque would just cause the engine to move upward. The way the mounts and brackets are, it cannot slide back- impossible.
With no reverse and the transmission having a noise, something broke inside. If you pull the pan down you will probably see metal pieces. Sounds like the trans I going to have to come out for repairs.
With no reverse and the transmission having a noise, something broke inside. If you pull the pan down you will probably see metal pieces. Sounds like the trans I going to have to come out for repairs.
-
- Similar Topics
- Replies
- Views
- Last post
-
-
New post 92 silverado 7.4 liter manual trans wont turn over
by stevep » Wed Nov 02, 2016 7:29 pm » in Chevy Trucks - 1 Replies
- 11487 Views
-
Last post by carriedi
Thu Nov 03, 2016 12:26 am
-
-
-
New post 1992.Silverado K3500 7.4 Liter,Manual Trans
by stevep » Mon Dec 18, 2017 6:06 pm » in Chevy Silverado - 3 Replies
- 19549 Views
-
Last post by carriedi
Thu Feb 01, 2018 12:17 pm
-
-
- 1 Replies
- 6126 Views
-
Last post by carriedi
Thu Jul 17, 2014 11:50 pm
-
- 1 Replies
- 6606 Views
-
Last post by carriedi
Wed Mar 23, 2016 10:17 am
-
-
New post Trailblazer Compression Problem
by Fmcclure » Wed Nov 29, 2017 12:16 am » in Chevy Trailblazer - 1 Replies
- 11164 Views
-
Last post by carriedi
Thu Nov 30, 2017 12:49 pm
-